How to Install a Ghost Immobiliser
A ghost immobiliser guards your vehicle from key cloning and hacking. It prevents the engine from running unless it is started using a PIN code, which can be as long as 20 characters.
This extra layer of protection is not visible to thieves who may not be aware of it. Certain systems have an app which allows the owner to disarm their immobiliser in the event of forgetting their PIN or use the service/valet mode.
Connecting the vehicle's CAN Bus
The Ghost 2 Immobiliser is a cutting-edge security system, can be integrated directly into the ECU of your vehicle. It is a subtle security barrier against thieves. It is highly efficient and user-friendly. This makes it a valuable asset to your vehicle's arsenal of security. However, just like any other anti-theft device, it is not foolproof and requires regular maintenance to ensure its operation. Fortunately, this guide can assist you in getting the most out of the Ghost 2 Immobiliser.
CAN (Controller Area Network) is a robust serial networking system that lets microcontrollers communicate with each other over small distances. Central control units is not required. It is designed to multiplex electrical wiring in vehicles, which saves on copper. It offers many advantages, including low cost and easy use.
The CAN protocol is used in most modern cars to communicate with the engine management system, transmission controller, steering control module and air conditioning controls and more. It also relays information from sensors like speed sensors and other inputs, to control the various features of the car. The CAN bus is able to monitor the health of these different components. It could stop the vehicle from starting if it is in an unsafe condition.
It's crucial to understand how the CAN bus functions and how it is secured. The CAN bus is an excellent method to add new features to your vehicle, but it's essential to secure it from threats such as hackers and other. The best method to achieve this is to install a firewall and monitoring your CAN bus with software.
Ghost2's discreet control unit is hidden inside the car's wiring harness or dashboard, eliminating the possibility of a thief physically altering it. It's also impossible to reset the PIN or emergency code without access to the vehicle.
If you have to surrender your vehicle to a valet parking service, maintenance or for any other reason, you can use the Transport Mode. This option disables the Ghost immobiliser's ignition and keyfob functions and will only come back on when the vehicle reaches 31 mph for 15 minutes.
How to create a PIN code
The Ghost immobiliser is an effective security device that shields your vehicle from thieves. The patented technology makes use of an PIN to shut down the engine of the vehicle and stop it from starting without the right code, or a valid fob/mobile. The system's subtle design ensures the system is not noticed and provides unrivaled protection against theft. Moreover the system is TASSA certified and can result in significant savings on insurance premiums for cars.
During the installation, the Ghost system goes into a learning mode to record the sequence of buttons that are pressed to create your unique pin code. The installer will guide you through activating the system after the pin code is created. Once activated, the Ghost system will disable your vehicle's starter motor until a valid pin code is entered or the vehicle is switched to transport mode. This makes it difficult for thieves or cloners who want to hack or replicate your starter system.
Installing an Ghost immobiliser is simple, but it is important to follow the detailed instructions in the user guide to ensure proper operation. Multimeters and basic hand tools are a good way to check electrical values. Insulation tape, heat shrink tubing and cable ties are a good option to shield exposed wiring. Also, be sure to check the system frequently to spot any issues or potential mistakes.
After the installation is completed it is crucial to perform a final check of the system prior to turning on the ignition in your vehicle. Ghost immobilisers will arm themselves after 3 to 30 seconds, depending on the model of your car. It also has a Service/Valet mode that allows you to temporarily disable the system while servicing your vehicle or valet parking.
The immobiliser should be placed in a hidden location beneath the dashboard or steering wheel. Make use of a small piece of duct tape or paint over the wires CAN H and L to make them easier to locate when testing. In addition the CAN H and CAN L wires should be connected to a power source that is able to provide continuous 12V. It is also essential to check the connections following testing, as misidentifying these wires can cause the system to fail.
Invoking the system
A ghost immobiliser blocks the car from starting unless you press a few buttons inside the vehicle, usually on the steering wheel or door panel, or the central console. The sequence is decided by the user and can be changed as needed. Once activated, the system cannot be removed. This is a fantastic option for anyone who wants to secure their vehicle from theft.
The device is not designed to be detected by modern diagnostics and code-grabbing techniques. It also doesn't send radio signals which makes it difficult for thieves to identify the device.
If the device is identified, it will stop the engine from starting and sound an alarm with a loud sound to deter thieves. The device can be used to monitor the location of the vehicle and help police track it down in the event of theft.
Contact Car Specalist Customs for a estimate or to discuss your options in an immobiliser that is ghost-like. We are able to install ghost immobilisers in your vehicle. We will ensure that it is placed in a place that is hard to reach. We can also install additional security measures, such as a kill switch or wheel lock, to ensure your vehicle is secure from thieves.
Disarming the System
If you have an Ghost immobiliser that is fitted to your vehicle, it's vital to know how to disarm it. This is useful in case you forget your keys or your car battery dies. The system has a unique PIN code that only you are aware of. It cannot start the car without this code. Pressing a combination buttons on the dashboard or steering wheel is the easiest method to enter your code. This is a simpler method than using the key fob and it also keeps anyone from copying your remote.
Ghost2 isn't intrusive unlike some aftermarket immobilisers which require cutting wires to facilitate installation. It also works with the CAN bus system of your vehicle in order to function. Its most notable feature is its ability bypass the engine without impacting your vehicle's normal functions, making it difficult for thieves to use signal boosters or duplicate your car key. It doesn't emit radio frequencies, which means thieves won't be able to detect it.
The Ghost system also comes with the Transport Mode, which allows you to temporarily disable the security system in occasions like transportation or servicing. This feature is a great option when you want to lend your vehicle to a person who isn't sharing the PIN code, or when you wish to secure your vehicle while driving it. To activate Transport Mode, press the service button five times within a period of 2 seconds. The Ghost system will confirm activation via 5 signal signals.
Keep the emergency code inside your vehicle in a safe place. If ghost 2 immobiliser near me The Keylab get locked out of your car, you can call the company or technician who installed the system, and they'll give you the code. If you cannot reach them You can always try contacting an authorized dealer, but this will involve verification procedures and could incur additional charges.
This system is not just convenient, but it can also protect your vehicle from theft and lower the cost of insurance. Many insurance companies offer lower monthly premiums or even financial incentives for installing this anti-theft system.